How To Repair Clapboard Siding

Clapboard is a class of the wooden siding of a building in the class of horizontal boards often overlapping each other. In some areas, clapboards were traditionally left as raw forest, relying upon air circulation and the use of semi-hardwoods then that the boards are kept from rotting. However, the boards eventually go grey every bit the tannins are washed out from the forest. The stride-by-pace guide provides more details on how to repair the clapboard siding in Calgary.

The Process Of Repairing Clapboard Siding

Step 1: Pull loose nails from clapboard siding

Loose nails may appear on the siding due to termite infestation or subsequently the clapboard siding is eaten away by rodents. Sometimes just every bit a result of moisture-induced rot. The loose nails may be hand-pulled easily and removed.
Rancid siding can also be removed at this stage. Be certain to remove all rotted clapboards and make sure that simply the layers are removed.

Step ii: Tap a flat bar from nether the siding to loosen nails

If in that location are nails that are however tightly stock-still on the strong siding boards, tapping with a bar may help to loosen them. You could also use a hammer to tap them gently until they go loose and easy to remove. Once they are loose, you can employ a claw hammer to pull them out of the siding.

Step 3: Snoop the remaining pieces of onetime clapboard out from behind the expletive to a higher place

Make sure all the affected siding boards are removed then that proper replacement is washed.

Step iv: Remove vertical caulk joints

Any vertical caulk joints existing betwixt the end boards and siding should be removed using an edge such as the knife or a sharp chisel.

Step v: Clapboard with a department damage

Where only a section of the clapboard is damaged, marking a new articulation using a speed square and cut off the spoiled portion using a circular saw. In case of damages caused past termites or moisture rot, cut the section out completely and supercede information technology with a new section of wood.
You will need to exist gentle and have your fourth dimension not to damage the siding boards above and below.

Step six: Remove areas damaged past termite

Use a reciprocating saw to cut the outline of the damaged woods for easy removal. Follow the outline using a circular saw and brand vertical cuts with the reciprocating saw. When the outline is articulate cut, use a wood chisel and mallet to remove the damaged wood.

Step 7: Utilize a sill to patch the siding damage

Measure the length and width of the sill removed. Cut out 2 pieces of lumber, treat them, and nail them together in order to achieve the desired thickness. Using a sled hammer, set the replacement sill into the hole.
A tighter fix can be achieved by nailing the sill into the neighbouring sill. Holes tin can too be drilled around the perimeter of the patch and filled with epoxy to arrive fifty-fifty stronger.

Step 8: Add new siding

Before this is done, it is recommended that you back prime the clapboard with oil-based primer so equally to protect it against futurity insect damages.
Use advisable starter strips of treated lumber on the sill exactly at the point where the lowermost layer of sliding will go upwards. When this has been done, cut clapboard siding using a mitre saw. Nail it to the starter strips and measure out the depth to ensure consistency with the existing courses above.
In case y'all have a clapboard that is too short to span a wall, spice two together using a 45-degree scarf joint, then apply a sealant to the ends, fit them together and drive one boom through the overlapping board ½ inch to the side of the joint.

Step 9: Pigment and prime number the siding

Once the very showtime siding is installed, add together the rest by slipping them under the courses to a higher place and securing each 1 of them with nails. Be sure to caulk the end joint as well as prime the forepart of each clapboard and let the primer to dry.
One time the primer is dry, apply the final coat of paint to march the house. You lot can use the leftover paint from your initial chore or take a bit of the staff you pried off to your nearest pigment store to become the all-time match for your repair.